About the Diamond Facial Protocol
Learn a variety of modalities to create a custom facial.
Procedure
STEP 1: Double Cleanse
Purpose: Remove makeup, oil, and impurities; prep skin for treatment.
Start with Viktoria DéAnn Purifying Cleanser
Follow with Viktoria DéAnn Balancing Cleanser
Substitutions (based on skin type):
Hale & Hush Quiet Wash (for sensitive skin)
Hale & Hush Clarify Wash (for acne-prone skin)
ClearChoice Mandelic Acid Cleanser (exfoliating option)
STEP 2: Exfoliation
Purpose: Gently remove skin cells and prime the skin for better penetration.
Primary protocol:
Apply a thin layer of Viktoria DéAnn 5% Lactic + Collagen Serum
Leave on for 3–5 minutes; it’s self-neutralizing and non-invasive
Substitute Exfoliation:
Use DiamondTome Microdermabrasion instead for gentle mechanical exfoliation (light suction and manual pass to avoid overstimulating before nano-channeling)
STEP 3: Peptide Layering
Purpose: Deliver targeted anti-aging and reparative signals to the skin.
Apply each of the following serums, allowing 1–2 minutes between each for full absorption:
Pepti-Lift – for lifting and firming
Pepti-Tone – for improving skin tone and elasticity
Pepti-Repair – for healing and barrier restoration
💡 Pro Tip: Apply directly to the skin (not gloves or fingers), using 4–6 drops per serum.
STEP 4: Hydration Infusion
Purpose: Restore and enhance skin hydration at multiple levels.
Apply Low Molecular Weight Hyaluronic Acid
Infused with Hydro Wand (compatible with DT2, DT3, NewApeel, Petite)
Then layer High Molecular Weight Hyaluronic Acid
Used as slip for the Skin Wand Pro nano-channeling step
STEP 5: Nano-Channeling
Purpose: Enhance penetration of active ingredients using non-invasive technology.
Use Skin Wand Pro with a 0.25 mm tip
Divide face into zones (forehead, cheeks, chin, etc.)
Gently glide over each zone in a consistent pattern
📝 Note: The Skin Wand Pro Home version uses a 0.15 mm tip—ideal for retail/home care.
STEP 6: BioCellulose Mask & Microcurrent
Purpose: Soothe, hydrate, and amplify treatment results with lifting energy.
Apply Viktoria DéAnn Nano Mask or Bel Mondo Beauty BioCellulose Mask
While the mask is on, perform microcurrent (conduct directly through the mask)
No conductive gel needed
Enhances product absorption and delivers visible lifting
Optional Final Steps (Retail/Home Recommendations)
Apply Pepti-Repair or Pepti-Hyaluronic as a finishing serum
Recommend Skin Wand Pro Home Kit + peptide minis for post-treatment retail care
Add SPF if client is exposed to sunlight after session
Cautions & Contraindications
Microcurrent is intended for facial stimulation and should not be used if the following indications are present:
- Pregnancy
- Seizures
- Cancer or tumors
- Cardiac pacemaker, or any electronic implanted defibrillator, simulators, or electronic devices as possible interference with these devices may occur
- Do not use if prone to phlebitis, thrombosis, or on varicose veins
Perform protocol on individuals with normal skin. Do not use on skin that is blistered, infected, or has cancerous lesions.
Intended for cosmetic use only and for individuals in good health. As with any medical condition or after facial surgery of any kind, please consult your physician before use.
Wait a minimum of 10 days before using microcurrent after the following procedures:
- Botox
- Injections and/or fillers
- Micro-needling (use after skin has fully healed)
Reminders:
Set up a clean and organized workspace with all necessary tools and products within reach.
Consult with the client to understand their skin type, concerns, and any allergies or sensitivities.
Perform a skin analysis to determine the most suitable products and treatment for the client's skin.
Proceed with the facial treatment following the appropriate steps based on the client's skin needs.
Conclude the facial with appropriate moisturization and SPF protection for the client's skin type.
Recommend a skincare routine and products for the client to maintain the benefits of the facial at home